Search Results

In order to reduce exhaust emission and combustion noise and to improve fuel consumption, the effects of the combustion system parameters of a diesel engine, such as injection pressure, injection nozzle hole diameter, swirl ratio, and EGR rate on exhaust emissions, combustion noise and fuel consumption are investigated and described in detail by analyzing rate of heat release, needle valve lift and injection pressure. Based on these results, reduction of exhaust emission and combustion noise and improvement of fuel consumption are described in the latter part of this paper. These results are shown as follows. The smaller nozzle hole diameter is effective for reducing smoke and PM, and by optimizing the injection timing and swirl ratio, NOx can also be reduced. In addition to the above, by applying EGR and higher injection pressure it is possible to improve the fuel consumption with the remaining low NOx and PM.

Flow and flame structure visualization and modeling were performed to clarify the characteristics of bulk flow, turbulence and mixing in a four-valve engine to adopt the lean combustion concept named “Barrel-Stratification” to the larger displacement center-spark four-valve engine. It was found that the partitions provided in the intake port and the tumble-control piston with a curved-top configuration were effective to enhance the lean combustion of such an engine. By these methods, the fuel distribution in the intake port and the in-cylinder bulk flow structure are optimized, so that the relatively rich mixture zone is arranged around the spark plug. The tumble-control piston also contributes to optimize the flow field structure after the distortion of tumble and to enable stable lean combustion.

This paper presents a new torque distribution system-“Right/Left Torque Control System”, aimed at improving a vehicle's cornering properties by using yaw moment control. The torque transfer mechanisms of this system have been analyzed. Also, a yaw moment control algorithm using yaw rate feedback control has been designed. Next, vehicle cornering properties were evaluated using numerical simulation developed from data taken from an actual vehicle. As a result, improvements were achieved in the maneuverability and stability of a vehicle during cornering.

The relationship between MTBE-blended gasoline properties and warm-up driveability is investigated by focusing on the transient combustion air-fuel ratio that strongly relates to the combustion state of the engine. As a result, although warm-up driveability of MTBE-free gasoline has a high correlation with 50% distillation temperature (T50) and a high correlation with 100°C distillation volume (E100), the correlation is found to be low when blended with MTBE. Various formulas that improve correlation with peak excess air ratio (λ) by correcting T50 and E100 for the amount of MTBE blended are examined. The formula for which the highest determination coefficient is obtained is proposed as a new driveability index (DI) that can also be applied to MTBE-blended gasoline. In addition, the effect on driveability by gasoline base materials using this new DI also is investigated.

Novel combustion control technologies for the direct injection SI engine have been developed. By adopting up-right straight intake ports to generate air tumble, an electro-magnetic swirl injector to realize optimized spray dispersion and atomization and a compact piston cavity to maintain charge stratification, it has become possible to achieve super-lean stratified combustion for higher thermal efficiency under partial loads as well as homogeneous combustion to realize higher performance at full loads. At partial loads, fuel is injected into the piston cavity during the later stage of the compression stroke. Any fuel spray impinging on the cavity wall is directed to the spark plug. Tumbling air flow in the cavity also assists the conservation of the rich mixture zone around the spark plug. Stable combustion can be realized under a air fuel ratio exceeding 40. At higher loads, fuel is injected during the early stage of the intake stroke.

In response to stringent particulate matter (PM) emission regulations worldwide, developments of diesel particulate filter (DPF) continue apace in addition to engine modification for PM reduction. Particularly with buses used in urban areas, reduction methods in black smoke emissions are being researched in addition to the efforts to satisfy the aforementioned PM regulations. The system described in this paper was developed for use mainly with buses in large urban concentrations. The system described in this paper mainly consists of both wall-flow monolith filters for filtration of PM emissions and electric heaters for regeneration. A key feature of this system is that exhaust gas is used for effective combustion of PM during regeneration. With conventional systems, airpumps have been used to feed air for PM combustion during regeneration. With the new system, however, the use of an air pump was discontinued due to durability and cost considerations.

The major problems of the various mixture formation concepts for direct injection gasoline engines that have been proposed up to the present were caused by the difficulties of preparing the mixture with adequate strength at spark plug in wide range of engine operating conditions. Novel combustion control technologies proposed by Mitsubishi is one of the solution for these problems. By adopting upright straight intake ports to generate air tumble, an electromagnetic swirl injector to realize optimized spray dispersion and atomization and a compact piston cavity to maintain charge stratification, it has become possible to achieve super-lean stratified combustion for higher thermal efficiency under partial loads as well as homogeneous combustion to realize higher performance at full loads. GDI™ (Gasoline Direct Injection) engine adopting these technologies is developed. At partial loads, fuel economy improvement exceeding 30 % is realized.

Passenger cars with sunroofs sometimes experience a low frequency pulsation noise called “wind throb” when traveling with the roof open. This “wind throb” should be suppressed because it is an unpleasant noise which can adversely affect the acoustic environment inside a car. In this paper, 3-dimensional numerical flow analysis is applied around a car body to investigate the wind throb phenomenon. The computational scheme and the modeling method of the car body is first described. A flow visualization test in a water tunnel was completed for the simple car body shape to compare against the numerical procedure. The numerical and the visualized results compared well and the numerical simulation method employed was considered to be a reliable tool to analyze the wind throb phenomenon. Calculated results of pressure and vorticity distribution in the sunroof opening were analyzed with the spectrum of pressure fluctuation at the sunroof opening with and without a deflector.

A new combustion system - called MCA-JET- has been developed to improve combustion under the low speed, low load conditions typical of urban driving. Engines with this new system incorporate a special “jet valve”, in addition to the inlet and exhaust valves of the conventional combustion chamber, which directs air or a super-lean mixture towards the spark plug, and induces a strong swirling flow in the cylinder. This swirl persists during the compression and expansion processes, moves the mixture spirally and helps the flame to propagate. As a result, the combustion of lean mixtures, including those with exhaust gas recirculation, can be carried out rapidly and thus the fuel economy improved.

Mitsubishi has developed the new, compact, water-cooled vertical type 2-cylinder diesel engine model K2AS and brought it to market in spring of '82. The K2AS is a small-sized engine of 451 cc total displacement and 10HP/3600 rpm maximum output. Its weight of 58 kg is light enough to use this diesel engine for various machines which have formerly been driven by gasoline engines. The well matched combustion chamber and injection system realize low fuel consumption, low noise and easy engine starting. High durability is also assured by various kinds of reliability evaluation. Features of K2AS are outlined below.

Mitsubishi Motors Corporation presents the newly-developed 2-liter engine, which we have named SIRIUS DASH. The SIRIUS DASH engine, with its compound intake system, features great performance in both high and low speed ranges while keeping fuel consumption low. The compound intake system operates the 3 valves in 2 stages. When engine speed is low, just one intake valve is used, but when engine speed increases, two intake valves are used. And to make this engine truly extraordinary, we added a turbocharger with an intercooler, and equipped the whole thing with a total electonic control system. Generally, high performance engines which have large inlet ports and high speed type valve timing enabling them to intake sufficient air for high performance at high speeds. The problem is here that when speed is dropped, combustion becomes unstable at the expense of torque and fuel consumption.

An analysis of the static behavior of T-shaped joint is presented. Advanced testings by laser holography and infrared ray stress wave analyzers verified the surface deformation and the stress concentration of joint area, which are very important factors of thin-walled joint stiffness. The definition of structural joint stiffness is attempted, and the relationship between structural joint stiffness and sizes(dimension) of the constructing members is obtained in case of a thin-walled T-shaped member with rectangular cross section. The parametric study to accomplish weight reduction, while maintaining the necessary structural joint stiffness, is described in case of Rocker to Center pillar. The numerical analysis of body structure considering the structural joint stiffness shows better accuracy as compared with the analysis with the joint assumed rigid.

The engine performance and emissions characteristics of a single-cylinder DI diesel engine were experimentally investigated. The combustion chamber walls of the engine were thermally insulated with ceramic materials of SSN (Sintered Silicon Nitride) and PSZ (Partially Stabilized Zirconia). Fuel economy and emissions characteristics were improved by insulating selected locations of the combustion chamber walls. The selective insulation helped to create activated diffusion combustion and resulted in more efficient use of the intake air.

Methanol has a poor self-ignition property and thus requires some kind of ignition assist system. Our evaluation of two such systems, a spark-assisted type and a glow-assisted type, indicated that these systems had room for improvement in terms of combustion stability and thermal efficiency in the low-load range. Combustion improvements in the low-load range were therefore carried out by increasing the compression ratio, adopting an injection nozzle with multiple holes and providing an ignition chamber. This has resulted in the successful development of a glow-assisted methanol engine with full-load performance equivalent or superior to a base diesel engine and with lower NOx emission. For practical application of this engine, further improvements in durability and reliability are to be made.

A particulate trap oxidizer system to reduce diesel particulate emissions has been developed. This system consists of a ceramic foam filter with an optimum volume, shape, and mesh number in terms of collection efficiency, pressure loss and particulate blow-off; a catalyst with a low activated-temperature for particulate incineration and with no sulfate formation during highway driving; and a regeneration system which prevents particulate overcollection during long-term continuous low-load/low-speed driving where it is difficult to achieve self-burning of particulates with a catalytic reaction. This paper describes the development of the particulate trap oxidizer system with these technologies and presents the results of practicability evaluations and 50,000-mile vehicle durability tests.

Auto-regeneration of diesel particulate traps, particularly combustion mode of soot in a wall flow filter with fuel additives, was investigated using a diesel engine of a light duty truck and truck itself. Soot burning in the trap and regeneration were observed under any engine operating condition including prolonged idling and stop-and-go driving at 0.18g metal/1 dosage of a mixture of copper and lead in the fuels. However, trap life was limited by ash clogging due to the metallic compounds. Although the influence of metallic additives on the environment was debatable, test results of the trap durability and calculations of soot burning based on the thermal ignition theory indicated that dosage and kind of fuel additives should be optimized in view of both trap life and reliability of soot burning.

The adoption of the diesel engine EGR systems, and increased uses of alcohol in spark ignited engines require wear resistant and low maintenance valve trains. Silicon nitride ceramic inserts were pressureless-sintered and successfully die-cast in rocker arms contacting the overhead cams in the valve trains. As fired, the insert sliding surface was fine and precise, eliminating any further processing. The comosite structure was machined with the sliding surface as a reference plane. Beside inherent high wear resistance, these lighter inserts reduced inertial forces of the trains and the torque required to drive the cams. The hard, brittle ceramics and a softer, more elastic aluminum alloy made the structure more durable and reliable. The process of development includes characterization, screening, manufacturing and quality control of the materials, and determination of wear resistance and reliability for this new structure.

A Vehicle Vibration Control System by Active Control has been developed. The experimental results using a 4-cylinder gasoline engine installed in a car showed that at the position of the driver's seat, the acceleration of the vibration was reduced by 16 dB. This system operates stably and at low cost because of having a feedforward system, so many applications can be expected in the near future as methods for vehicle vibration reduction.

There have been various predictions made concerning the future profile for automobiles but such predictions have in many cases been based solely on anticipated advances in technology. In presenting a profile for automobiles in the year 2000, the writers predict the evolution and transfiguration of automobiles, taking both phases in the changing social environment and technical trends into account. Interest in automobiles is expected to shift from hardware to software and then to humanware (i.e. more emphasis is placed on the relationship with human beings), and automobiles will evolve and transfigure reflecting these changes.

In order to investigate the effects of high injection pressure on engine performance and exhaust emissions, some experimental high injection pressure in-line pumps were made and tested. Increasing fuel spray momentum by high injection pressure could reduce smoke emission, but excessive increase in injection pressure was found not so effective in further reducing smoke emission. Accordingly, a high injection pressure should be accomplished within the low engine speed range a feature that has been very difficult to achieve for a conventional in-line pump. An electronic controlled injection-rate-control pump with a variable prestroke mechanism can provide higher injection pressure in low engine speed range and advances injection timing in high engine speed range. This pump can improve fuel economy in low engine speed range and emissions (smoke and particulate) over transient FTP for HDE's.